Scotsman CMS1402 Manuel de service

INTRODUCTIONTo the owner or user: This service manual isintended to provide you and the maintenance orservice technician with the information needed t

FREEZING CYCLE OPERATIONWater from the sump assembly is pumped to thewater distributor system at the top of eachevaporator plate. From the water distr

HARVEST CYCLE - HOT GAS BYPASS When the timer switches the icemaker into theharvest cycle, the finish relay is de-energized, andthe hot gas valve and

COMPONENT DESCRIPTIONCube Size ControlThis reverse acting thermostat controls the lengthof the freezing cycle. It is sensing the temperatureof the suc

COMPONENT DESCRIPTIONBin Level ControlThis electronic control uses sound waves tomeasure the distance between the bottom of theice machine and the top

COMPONENT DESCRIPTIONWater Inlet Solenoid Valve The water inlet solenoid valve fills the sumpassembly with water. Extra water overflows out theoverflo

CLEANING//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

CLEANINGAIR COOLED CONDENSER1. Disconnect electrical power.2. Remove front panel.3. Clean or replace the air filter.4. Check to see that the inside of

ADJUSTMENTSAdjustment Of The Cube Size Control//////////////////////////////CAUTION////////////////////////////////////BEFORE adjusting the cube size

ADJUSTMENTSAdjustment Of The Timer & Switch AssemblyOne complete revolution of the cam on the timertakes eight minutes. The normal setting is thre

SYSTEM SPECIFICATIONSThe following numbers can be used as a guideline . There will be some variation from unit to unit.Typical Cycle Time••14-16 minut

Model Number Dimensions (w/o bin)W" x D" x H"Basic Electrical Minimum CircuitAmpacity*MaximumFuse SizeRefrigerantChargeCondenser TypeCM

SERVICE DIAGNOSIS: Electrical and/or AdjustmentsSYMPTOM POSSIBLE CAUSE PROBABLE FIXNothing operates Bin level control holding machine off Bin is full

SERVICE DIAGNOSIS: Refrigeration and/or MechanicalSYMPTOM POSSIBLE CAUSE PROBABLE FIXPoor harvest Too short harvest time Check and adjust harvest time

CONDITION DETERMINE CAUSE PROBABLE CORRECTIONIce Machine does not run, it haspower to it, the high pressure controlis closed, the on/off switch is set

REMOVAL AND REPLACEMENTWater Distributor Tubes And Manifold Tubes To remove the water distributor tube and manifoldtube: 1. Remove the front panel. 2.

Water Pump1. Remove front panel.2. Unplug water pump electrical connection.3. Drain water reservoir.4. Use corbin clamp pliers to loosen and slidecorb

REFRIGERATION SERVICEGeneral:••Scotsman recommends that any work on therefrigeration system only be done when it iscertain that the system needs repai

FOR THE INSTALLER: Location & AssemblyLocation:After uncrating and inspection, the unit is ready forinstallation. It is important that the machine

FOR THE INSTALLER: Location & AssemblyStacking InstructionsA stacking kit, KSCMS48, is required tointerconnect the ice level controls, seal thefr

FOR THE ELECTRICIAN SEE NAMEPLATE for current requirements todetermine wire size to be used for electricalhookup. The cuber requires a solid chassis

FOR THE PLUMBERFOLLOW ALL LOCAL CODES:The recommended water supply line is a 3/8-inchO.D. copper tubing with a minimum operatingpressure of 20 PSIG an

FINAL CHECK LIST1. Is the cabinet in a room where ambienttemperatures are within the minimum andmaximum temperatures specified?2. Is there at least si

INITIAL START UP1. Remove the front panels by removing screws atthe base and pulling out.2. Remove two screws and the control box cover.3. Check that

INITIAL START UP12. After an ice harvest check Cube Size.There is just enough water available in thereservoir to make one full sized batch of cubes.Th