TO THE OWNER OR USER:The service manual you are reading is intended toprovide you, and the maintenance or servicetechnician, with the information need
COMPONENT DESCRIPTION: EvaporatorEvaporator: A refrigerated vertical tube filledwater and containing a water seal and auger.Auger: A solid stainless
ELECTRICAL SEQUENCERefer the wiring diagram as needed.Each system is separateIf the machine is switched off at the master switch,but is otherwise read
OPERATIONWaterWater enters the machine through the 3/8" maleflare at the rear of the cabinet, goes to the waterreservoir which it enters through
OPERATION: RefrigerationThe remote high sidesupplies high pressureliquid R502 to the liquidline connection on theice machine. After thesight glass, th
MAINTENANCE AND CLEANING//////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
MAINTENANCE////////////////////////////WARNING////////////////////////////Disconnect electrical power before beginning.///////////////////////////////
CLEANINGIn some installations the water supply to theicemaker will be so concentrated with dissolvedminerals, (such as calcium carbonate) that as ice
SERVICE DIAGNOSIS: Condition - No Ice Being ProducedSTATUS: NOTHING OPERATESA. Check: Voltage to the unit, restore it if there is none. Compare to the
SERVICE DIAGNOSIS: Condition - No Ice Being ProducedSTATUS: NOTHING OPERATESF. Check: The gear motor, if it will not run, the liquid line valve will n
A. Check the liquid line valve relay.The relay is on the circuit board, if it does not supply power to the liquid line valve, the valve will not open.
FOR THE INSTALLER: SpecificationsThe FM2400RH is designed to fit the Scotsmanstorage bins BH800 or B90. Leg kit KLP4 isrecommended when using both the
WATER RESERVOIR 1. Shut off the water supply to the icemaker.2. Remove front panel and reservoir cover.3. To remove float only, "A" models:
REMOVAL AND REPLACEMENT: Bearing And BreakerNote: Removal of the auger, water seal,evaporator and gearmotor must begin at the top ofthe assembly.To Re
To Remove the Auger:Turn off the water to the machine, and unclip theevaporator drain hose, pull it down and drain theevaporator into the bin or a con
/////////////////////////////WARNING///////////////////////////Disconnect the electrical power to the machineat the building source BEFORE proceedingw
To Replace the Evaporator:(Assuming all the steps for removal of the thrustbearing, breaker, auger, and water seal have beenperformed.)1. Shut the han
To Remove and Repair the GearmotorAssembly:(Assuming that the procedures through removal ofthe water seal have been performed.)1. Remove the electrica
///////////////////////////////////////////////////////////////////////WARNING//////////////////////////////////////////////////////////////////These
Water Level1. Unplug “water sen” connector from controlboard.2. Plug “water sen” connector from Scotsmantester into circuit board.a. Move “water” sw
FOR THE INSTALLERSelect the Location: The unit can only be installed indoorswithin the limitations described onpage 2.The ice machine will have to bec
Electrical Connections:Locate the nameplate for the current requirements,and then determine the wire size and type per theNational Electric Code. The
FOR THE PLUMBERCONFORM TO ALL APPLICABLE CODESWater Supply:The recommended water supply line is 3/8" O.D.copper tubing, with a minimum operation
FOR THE INSTALLER: Final Check List1. Is the unit installed where the air and watertemperatures are within and will remain within thelimitations for t
INITIAL START UP1. Remove the top and front panels.2. Open the water valve, and observe that the twofloat reservoirs fill up with water and shut off.3
COMPONENT IDENTIFICATIONLiquid line valve(s)These valves operate to turn the ice makingprocess on and off.When the ice level drops in the ice chute, t
COMPONENT DESCRIPTION: Control BoxCircuit Board: Controlling the ice machinethrough sensors and relays. The sensors are: icelevel, and water level.
Commentaires sur ces manuels